Ubiquiti Networks USP PDU PRO

Always looking for a better PDU for our labs, we recently took a look at (and took apart) Ubiquiti’s USP-PDU-PRO. A 2U PDU with a mix of both standard North American AC outlets and USB-C ports for DC power, the USP-PDU-PRO is designed to synergize with Ubiquiti’s other networking products and its UniFi ecosystem. Fittingly, while this is first and foremost a power distribution unit, it has quite a few features that we normally do not find on other PDUs.

As a quick note, this is not a mini-review sponsored or supported by Ubiquiti since we did not sign the NDA they provided to STH. This is just a unit that we purchased and decided to do an overview with it.

Ubiquiti USP-PDU-PRO External Hardware Overview

Starting from the front of the USP-PDU-PRO, we find 16 NEMA 5-15 sockets. 12 of them are lined up in a dense formation along the top row of the PDU, while 4 more are spaced out along the bottom row.

Ubiquiti Networks USP PDU PRO Front 1

Focusing on the left side, here is where we will find 4 USB-C ports as well for providing energy to low-power USB devices. Each port is limited to 2A@5V (10W), with the entire cluster of ports limited to 20 Watts overall.

Ubiquiti Networks USP PDU PRO USB C Ports

As we will see, this is fed by an internal 40W power supply, whose output is split between these ports and all of the other active features of the PDU.

On the lower-left side, we see one of those features with the 1.3-inch touchscreen, which is used for basic control of the PDU. Other than the circuit breaker and the factory reset buttons, there are no other controls on the USP-PDU-PRO, so the touchscreen is everything (at least until you get networking up and running).

Ubiquiti Networks USP PDU PRO Touchscreen

On that note, on the lower-right corner of the PDU we find three of the PDU’s four RJ45 Ethernet ports. The side port operates at 100Mbps, while the two top-to-bottom ports are full GbE ports, placed in position to allow for network redundancy. The 100M port 21 is the one we use to connect this back to our UniFi setup in the studio, but since it is not a high-speed link, 100Mbps is fine. We will discuss the other two links when we get to the rear gigabit Ethernet port.

Ubiquiti Networks USP PDU PRO 100 MbE RJ45 + GbE RJ45 Ports

It is also here where we find the tiny factory reset button.

And above that all, we have the circuit breaker button, conveniently placed at the front of the PDU. Some PDUs have large breakers, but this is a smaller recessed button. We have not had to use this yet.

Ubiquiti Networks USP PDU PRO Circuit Breaker

Around the rear, we find one more RJ45 Ethernet port, along with the PDU’s attached power cable.

Ubiquiti Networks USP PDU PRO Rear 1

This final Ethernet port is similarly GbE-capable like the front ports. It feels like the other ports are there mostly for features we have not used (and are not in the basic installation steps.) We found an installation video from 2021 that said you would use this port 24 “ISP” port to go to your modem, then the two 1GbE ports on the other side are “Reserved for Virtual Router Redundancy Support Coming Soon”. These days, most will just use the 100M port on the front for management.

Ubiquiti Networks USP PDU PRO GbE RJ45 Port

Meanwhile, the attached power cable features a typical NEMA 5-15 plug, alluding to the power limits of the device. Ubiquity has rated the USP-PDU-PRO to be able to handle a full 15A at 125V, distributing up to 1875 Watts – but it is not a PDU designed to plug into a higher voltage socket.

Ubiquiti Networks USP PDU PRO AC Power

Finally, taking a quick look at the sides, we find a bunch of screws and screw holes for mounting, but nothing else of note.

Ubiquiti Networks USP PDU PRO Side 2

Next, let us get inside and see how it is constructed.

Ubiquiti USP-PDU-PRO Internal Hardware Overview

Cracking open the PDU, we get to what is arguably a more interesting sight. Between the networking hardware, the control hardware operating the PDU, and the ability to individually power cycle each and every power outlet, there is a lot going on inside to enable all of the functionality.

Ubiquiti Networks USP PDU PRO Full Inside 1

The PDU features two PCBs in layers. The lower PCB features the bulk of the actual power hardware, as well as the networking hardware. Meanwhile the top PCB primarily houses the smarts of the device, as well as the components that make up its 40W internal DC power supply.

Ubiquiti Networks USP PDU PRO Inside 10

Along the top here, we can see how the AC outlets are wired, with common neutral and ground wires running through the outlets. The individual black wires connected to each AC outlet are the hot (live) wires, and are individually controlled to allow each power to be cycled as requested.

Ubiquiti Networks USP PDU PRO Inside 3

Going below deck, we can see the other end of those live wires, along with what appears to be a breaker next to each of them, likely to control the current flow. With 16 AC outlets, there are 16 of these breaker/ wire pairs throughout the PDU.

Ubiquiti Networks USP PDU PRO Inside 8

Along the top right corner, we find the USB-C port hardware. A small daughter board is connected back to the top layer PCB via a small ribbon cable, while power is provided via a separate cable coming in from a bit farther down.

Ubiquiti Networks USP PDU PRO Inside 5

While we are up here, we find the DC power supply hardware in more detail, including the various capacitors and chokes needed to transform the power. Multiple cables lead to and from here, supplying power for the various smart bits of the PDU, such as the SoC and Ethernet jacks.

Ubiquiti Networks USP PDU PRO Inside 4

It is also hard to miss the significant amount of compound laid out around many of these discrete electrical components.

Ubiquiti Networks USP PDU PRO Inside 6

We usually just show what is inside, and we will let others debate the merits of the PDU’s construction since we are not a safety ratings agency.

Next, let us get to the software and management because this has a lot more going on than a simple power strip.

Ubiquiti USP-PDU-PRO Software Features

All of that relatively complex control hardware, in turn, exists to drive the software functionality of the USP-PDU-PRO. While it can be used with its tiny front-panel touch screen, the device is ultimately meant to be best controlled from a UniFi controller. Once you plug that 100M port in, and have a network path to the controller, it will show up in the UniFi application where you can click to adopt the PDU.

Ubiquiti Networks USP PDU PRO Adopt In UniFi

With multiple Ubiquiti devices, you can bring them together to manage them. One neat feature with this is that you can add power intelligence to the environment. A common one would be if a connected system fails ping checks for some time, you can have the port power cycle in the event that it was a hard lock on the device. That is a feature that has been around in PDUs for a long time, and it sometimes is a lifesaver. It can also yield funny reboot cycles if there is another issue.

Ubiquiti Networks USP PDU PRO Port Information

And once setup, Ubiquiti’s software can show the state of each individual port and outlet – both AC and USB. Information on the Ethernet ports is also available in this view.

Ubiquiti Networks USP PDU PRO Power Outlet Power Cycle

Diving deeper, the software can also provide information on and control over a single outlet/ port. In this case, showing us that Outlet 8 is drawing around 48 Watts of power. It is here that we can also power cycle the port. Along with the manual option, the USP-PDU-PRO also offers a “modem power cycle” option, which can automatically cycle a port (i.e. the modem) if the network connection drops, in an attempt to restore it.

Ubiquiti Networks USP PDU PRO USB Power Cycle

Unfortunately, the same power metrics are not available for the USB-C ports. They can still be cycled, but the device cannot show what an individual USB-C port is pulling.

Ubiquiti Networks USP PDU PRO Front Angled 1

If you are in a Ubiquiti UniFi ecosystem, this is much easier than trying to manage an APC PDU that has remote power cycle and per-PDU and per-outlet metering, plus managing firmware updates. Part of the premium of this device is the added intelligence and ease of use.

Final Words

The USP-PDU-PRO is a network-enabled PDU that is designed to slot into a stack of other Ubiquiti hardware. As a higher-end PDU, it features most of what you would expect from such a device, including individual outlet/ port monitoring, remote access, and the ability to power cycle each port. While using it alongside other Ubiquiti products seems to be the best way to get the very most out of the PDU, it is not necessary to take advantage of the PDU’s core features.

Ubiquiti Networks USP PDU PRO Rack Ears 1

STH has roughly 50 PDUs in the studio and the lab at this point (excluding any being tested and in the various colocation racks.) Those run equipment we are reviewing, but also run lights for the studio’s sets and so forth. We tried the PylePro PCO885 2U PDU around the same time that we got this. Those PylePro units are roughly one-third the cost since their control is essentially a single big switch. In the meantime, we have stopped using the PylePro and now have purchased 6 of these USP-PDU-Pro units. That is a good indication of the impression they made on the STH team.